Island Green Woodworking

Poplar Lowboy - Cherry Finish Part -2-

2011-11-27T12:07:00.001-05:00

Now that my test boards are looking pretty good. Time to ready the wash-coat, so I mix equal parts, 3/4 cup of General Finishes High Performance ("HP") to 3/4 cup of water into clean pickle jar and using a stir stick, mix thoroughly.

I prep my garage, which has now temporarily become the spray room. Today Michigan's fall weather has cooled the air to about 40 degrees. Better get that portable heater going. Water-based finishes flow better in 60 to 70 degree temperatures, 70 is the optimum. I know, I know, its only the wash-coat, so temperature isn't too critical. Flowing out a wash-coat isn't the goal. Getting the wash-coat to soak into the wood is!

To clean the wood and raise the grain, I wipe down the exterior wood surfaces using a damp rag soaked in a mix of equal parts denatured alcohol and water. By mixing the denatured alcohol into the water, alcohol helps to speeds the dry so not to "over wet" the wood as you will with just plain water. Once the wood has dried, I scuff off the whiskers using 320 sandpaper and sand all my end grain to 600 grit, then clean the dust off (I did this already in my basement workshop)

Since my case is pure sapwood and knowing how thirsty sapwood is. I'm going to give it 2 good wet coats. Remember, we want a pretty good seal on the sapwood. Same goes for the Lowboy top even though its mostly heart wood. I don't want any chance of blotching, just in case I get heavy handed spraying the dye. Once the wash-coats have dried, a quick scuff with 320, then clean off the dust.

Poplar Lowboy - Cherry Finish Part -1-

2011-11-21T16:54:00.006-05:00

The Test Board...you do those, don't you??????

Sand the poplar to 180

Wash-coat is a General Finishes (water-based) High Performance Topcoat mixed in equal parts with water

Dye is General Finishes (water-based) Cinnamon

Topcoat is General Finishes High Performance

Stain is General Finishes (water-based) Black Cherry

This picture is of poplar sapwood dyed with the Cinnamon. Don't forget to first spray the board with the wash-coat mixture. The wash-coat will ensure even take-up of Cinnamon dye. Once the wash-coat is dry, scuff the raised grain with 320 sandpaper, then proceed to spray enough Cinnamon dye for an even background.

Once the Cinnamon dye has dried, I cover the left side of the test board with newspaper, spray the right side with a good wet coat of General Finishes water-based High Performance topcoat straight from the can, thus sealing in the dye allowing me to stain without hindering my dye. Basically, we'll be staining right over top of the topcoat, using our stain as a glaze.

Once the High Performance has dried, I remove the paper from the left side and apply 1 coat of General Finishes water-based Black Cherry stain over the entire board. Note how the stain took smoother and lighter on the right, which was first sprayed with the High Performance topcoat. The untreated left side took the stain darker.

The left board in the picture above, is entirely of poplar heartwood. I followed the above procedure sealing the dye over with topcoat. So here is the thing, since the heartwood board will tone or stain darker, due to the fact, poplar heart is darker than the whitish sapwood. The heart wood board will shade about 1 coat darker. So to even out, I had to apply a second coat of stain to the sapwood board.

General Finishes - Crosslinker Additive - Not In Retail Stores

2011-11-17T11:13:00.002-05:00

Word on the street is... General Finishes will no-longer sell their additive product called Crosslinker to the retail market. However, still available to the "professional" line of products in quart containers to mostly use in conjunction with General Finishes 450 product line. General Finishes have fortified their products and product lines making crosslinker mostly obsolete.

Crosslinker is an additive product which was sold separately to enrich certain General Finishes products, making then more durable and chemical resistant.

Used LVLP Tool Score - Iwata LPH400-134LV Spray Gun

2011-11-12T14:49:00.023-05:00

I purchased a used Iwata LPH400 - 134LV base-coat clear-coat spray gun from our local auto body store. The gun was used in the field for demo purposes. The kit included a1.3mm and 1.4mm needle and nozzle, along with 2 air caps and the 3M PPS disposable cup adapter along with the standard steel cup.

I understood the gun was run pretty hard and air was leaking past the trigger. So haggled them down to half the cost of body shop price new. The remaining thing to do is a complete rebuild on the gun.Unfortunately, the air valve is on back-order and should arrive in today's mail. I have all other parts.

A very cool gun that operates on less air than a standard HVLP sprayer. Air pressure at the gun should be set to 14-18 pounds with the trigger pulled and fan pattern fully opened, so 10 pounds at the air cap is achieved. Interesting thing about this gun, the fluid tip is scored. Its called "tulip shaped fluid nozzle" which helps with fluid atomization and produces less over spray than ordinary guns. So much so, that two painters can simultaneously paint a single car in the same spray booth.

So this weekend....test and tune spraying sealer...pic's will follow.

General Finishes Milk Paint

2010-11-22T23:01:00.236-05:00

Often times I see General Finishes “Milk Paint” being lumped in with the old timer Milk Paint. Folks will typically say "it’s not real Milk Paint, only water-based-acrylic paint like a wall paint," so the picture in the minds eye of every woodworker...... its just ordinary wall paint you buy at the five and dime and shame on General Finishes for its tricky wording!

Correct, General Fishes Milk Paint is not that rough old timer Milk Paint made with real cows milk dirt and firewood ashes. That would be like comparing a car to a pickup truck. One’s not better than the other, it just has different features for different jobs.

Yes, it’s acrylic base and is exterior durable, will stick to just about anything and is long lasting. General Finishes Milk Paints are made for wood used in the craft and furniture industry, and for that matter, anything wood. Just a high grade quality furniture paint.

Lets break it down, I believe "Milk Paint" is a term used, like "lacquer." and not Trademarked. Ok think about this, as finishes have evolve, we now must speak in terms of solvent based or water-based "lacquer." Take shellac for example, need to be careful with that! Target Coatings has water-based "shellac." So, correct to say, is your shellac cut with water or alcohol? You bet !

Don't get caught up in the label folks, as I stated earlier, finishes are formulated for different jobs.

Pine Shaker Clock - The Finish

2010-03-17T08:31:00.001-04:00

I spray 2 to 3 light coats of General Finishes Vintage Cherry water-based dye stain, straight from the can. Once the dye has dried, I begin by wiping the General Finishes water-based Shaker Maple stain over the dyed surface. Should the stain not take to your surface evenly, use paper towels damp with water and wipe the surface to pull the excess stain off. This is probably just a good idea anyway, for even color.

Now to the cool part, this allows you to achieve deeper color. First, I shoot a water-based topcoat over the dry Shaker Maple stain. In this case, I'm using the EM6000 production lacquer from Target Coatings and that will amber a bit like solvent nitro lacquer. Second, once the lacquer has dried, I lightly wipe with 320 paper and clean my surface. Then I glaze with the same Shaker Maple stain. So now we have stacked our color, which give's depth to your project and by the same token, will aid to even your color as well.

Once the stain has dried I shoot 2 coats about 2/3 mils thick (the point where your wet film finish starts to look blue) and call it done.

Tiger Maple Shaker Clock

2010-03-01T21:37:00.010-05:00

Tiger maple clock completed. My topcoat is the new General Finishes water based lacquer. Sprayed really nice, laid down flat and smooth.

Tiger Maple Shaker Clock

2010-02-07T12:29:00.026-05:00

Building a Shaker inspired clock from hard Tiger Maple , together with, one of pine, (top left). The case is rabbit joint construction, wood is 9/16 thick. I purchased the Tiger Maple from my friend Bob Kloes Bob has the most gorgeous maples I have ever seen, never has he let me down. Ummm, the pine, well that's just box store special.

Took a lot of flipping and flopping to get the grain and curl going the way I wanted. Rail and stile construction using the mini rail and stile bits from MLCS Woodworking.

I struggled with the door panel. It was milled from a single wide board and had cupped a good deal. I thought I could win the battle by placing the board in traction by wetting with water, then over bending and apply heat and steam. But once the board became acclimated, it bent right back. Enough time was being wasted. So I just wet the cup side, as soon as the wood relaxed, I began working the panel to final size then locked it into the rail & stile frame. So far so good.

Learn To Turn Part 3

2009-09-10T21:07:00.027-04:00

Respect your Elders (Acer Negundo) Box Elder Silly!

I had e-mailed Kevin and his Wife Terry at Powder Creek Sawmill, my goal, to take my turning up a notch! Sink my teeth into some of that beautiful Flame Box Elder. My expectation was a bowl between six to eight inches in diameter and two inches in height. Within a few days my little bundle of joy arrived.

Never before have I seen Box Elder up close and in person. I didn’t know what to expect. So down to the shop I go, draw my outline of a circle and band saw out (this step save you time on the lathe rounding your stock). Let me tell you something, put a piece of Flame Box in the lathe, see what happens to your heart rate. You pay attention brotha, you feel like your ready to play a fine musical instrument with thousands of people watching you. I have read how prized Flame Box Elder is to the turning junkies, trust me I’m about to find out why!

After roughing the blank out. I was amazed what I saw. Interesting pattern’s colors, even two insect holes. I wasn't expecting the finest qualities that nature had to offer. Think about it, I have spalt, curl and red flame all in one small block. So for about $30.00 will fetch you a nice piece like this.

Sprayed with a weak dye (a couple drops of Trans Tint Honey Amber to a full coffee cup of lacquer thinner, could use alcohol, however, lacquer thinner will dry quicker).

With the dye completely dry, I oiled the dye in with General Finishes Seal-A-Cell. A light scuff with 320 foam-backed paper to the dry oiled surface then I shoot one coat of a two pound cut of blond de-waxed shellac, locks everything down and readies the surface for the water based topcoat.

Scuff the dry shellac with 320 foam-backed paper, then apply five topcoats by hand using a cotton rag with General Finishes water-based High Performance Satin. Make sure to scuff with 320 between each coat. Once the topcoat has thoroughly cured. I rubbed out the bowl with a 2000 grit Abralon pad and finish off with a coat of wax.

Learn To Turn Part 2

2009-08-16T10:59:00.013-04:00

Like a moth to a light, I chucked up the bad boy! Went right for the good stuff. The turtle shell looking burl Maple! I made no plan, didn’t have a clue as to form. I’m a lathe turning artist by golly. Simply going to let things happen.

Safety First, I had asked around about turning “wild” type wood. I’ve heard, especially with the spalted woods, you need to be careful about the dust containing molds. Eye and sinus infections could result. So for me, on with a good respirator and eye protection.

I don’t have the high flautin bowl gouges the “real” turners do. Perhaps if the turning bug bites me hard, some day I’ll join that club. But I do have a set of “Sears Craftsman value pack turner specials” sitting on my bench. And since my chisels look every bit like they were dragged behind a car, (perhaps that is why our previous owner put an eyehook into each chisel handle,) needed sharpening.

Ok with sharp chisels, were ready to go! Things were going great till a few chunks came flying off, harmless though. Cut into a few soft spots. More worm/insect tunnels to cut through, but ultimately, arriving to a nice cylinder shape, smaller than I was hoping for, but doggoned, I had something to work with.

My Weed Vase, sanded smooth and 5 coats of General Finishes SEAL-A-CELL Clear. The Maple burl really drank in the oil, so basically keep coating till it won’t take any more.

Learn To Turn - Part 1

2009-08-13T20:54:00.019-04:00

Let me introduce to you, my lathe. It’s a 79-year-old Power King 9” lathe. I paid 150.00 off a Craigslist seller, included with the lathe, a new Rockler brand duplicator (not pictured). My intent was not to turn bowls or vases. Strictly, for cleaning up table legs on refinishing work.

So I sent my friend and fellow woodworker Bob Kloes, ("Bob") that lives in Wisconsin, who by the way sells some of the most beautiful figured woods you will ever see, an e-mail if he knew of someone selling turning blanks. So Bob knows a guy and asked what I was looking for? My comment to Bob “I have no clue!” Bob said not to worry and got working on it. Well look what showed up at my doorstep. I have from left to right 1 Maple blank and 2-burl Maple blanks.

Folks the only thing I have ever turned on my lathe was a pine 2x4 just messing around with coves and beads, that’s it! Oh great…go from the frying pan into the fire. I have three (3) beautiful chunks of wood, and one looks like a turtles shell or a compressed heap of knurled tree, (which I think is the really special one).

Heavy Duty Stress In Wood

2009-07-14T07:03:00.010-04:00

While ripping cedar boards yesterday I encountered heavy-duty wood stress. So much so, the board pinched between the table saw fence blade and splitter enough that I couldn't advance my 8’ board through the cut. Notice the gap under the board resting on the saw top. You should have seen the 1”x 1” strip that I was attempting to cut. It came off the blade “C” shaped and twisted from the wood tension.

Safety First

If this happens to you immediately stop feeding the board hold your board firmly in place, shut the saw down remove the board when blade stops spinning.

MLCS Matched Miniature Rail & Stile Router Bits

2009-06-20T07:53:00.025-04:00

The online Shaker Clock video over at Charles Neil Woodworking, Charles used the Eagle America/Price Cutter miniature “round” matched rail and stile bit set for the clock doors. As I write, the lower priced Price Cutter bit set is selling for $89.99 and not sure if the shipping is included?

So last week I was looking around on the Internet and found a Company called MLCS Woodworking. They sell router bits and other woodworking goodies and have the miniature “round” rail and stile matched bit set for $49.95 with free shipping so for you value seekers, that's a $40.00 savings.

Worked Great!

Found a little shop time, milled some pine to 9/16 and ran the MLCS Woodworking mini round rail and stile bits. It didn't take long to dial in the setup. This joint is not glued only pushed together by hand.

Kehoe Jig Sled Setup

2009-05-17T08:55:00.009-04:00

Here’s where you begin to work a little, the cool part. Now I didn’t pay that close attention to Charles in the Kehoe video (but I should of... I wasted a lot of time here where to start the index) but he did say it. Notice the picture and note the alignment of the stop (the thing with magnet attached) the sled and your wood. That is key, its your index point, you should now be ready to make your cut.

Here you will be making multiple test cuts to adjust your spline fit. First, set your blade angle as Charles instructs in the video. This is blade angle on your saw in relation to the angle of your dovetail cut, meaning insuring a proper fitting spline.

Second is the width of the spline. Set this up as Charles instructs in the video. I made a test cut using the pencil line which resulted in too wide of a spline. Note how I have moved away from my pencil line on the sled, this allows for a narrower spline. My goal is to have the spline centered in the dovetail cut.

Here the sled is through its full rang of motion. The sled must stop at the magnet or you will cut through the sled base! Cut and test cut and test!

Kehoe Jig Adjusting The Cut

2009-05-16T15:05:00.005-04:00

Oops, the first cut is too deep which causes the top portion of the cut to tear out from the rotating shank passing through the wood instead of the cutter surface. Too deep because I adjusted my router so the dovetail bearing was tracking or following dead center along the finger or slot of the jig.

My second cut (one on the right) was set with the bearing riding high enough on the finger (about half the bearing) with the top of the cutter just kissing or passing through the top of the cut. Just perfect! My pencil line is to help with the visual and not an aid for cutting or set up. Nothing difficult here at all.

The Kehoe Jig For Making Spline Dovetails

2009-05-14T21:36:00.008-04:00

In December 2008 the Kehoe Master Jig was a Charles Neil Contest prize which I was fortunate to win. Recently I had time to learn the basic jig. Before doing so, I suggest you watch the Charles Neil demonstration video first and along with the directions supplied with your jig.

I’m telling you this jig is super easy! Even easier if you already have experience machine cutting dovetails. The spline setup on the table saw was the most time consuming. But I would expect under an hour is probably about average for a first time . Next time I bet my setup should take less than 10 minuets. It’s the getting use to it part and test cuts making sure of a perfect fit.

Frankly, the supplied splines used as a gauge will get you as close to your fit as possible like Charles describes in the video. The two (2) setup cuts most time consuming will be table saw blade angle, necessary for a tight fit without gaps. The other is width of cut so splines center within the grove of your dovetail.

Kehoe Jig in position. If you have additional spring clamps in the shop, use them. I have four (4) holding the Jig down. Rather have a wee bit more holding power.

Speed Up Re-Coats Of Shellac

2009-04-07T19:44:00.005-04:00

So you just sprayed an awful looking first coat of shellac, orange peel you name it! You put down too heavy a coat. You don't have all day to wait for the shellac to completely dry and you want to get another coat on to build your topcoat. However, first, you will need to knock down high spots of orange peel to level out your surface before a re-coat.

Ok we all know the rule, a topcoat is dry when sanded, a white powder comes off the paper, (in this case I'm using amber shellac so it will be an amber color powder). Now my shellac only has about an hour of dry, my sandpaper is still digging into the shellac and loading up. The shellac is dry, just not dry enough to "dry sand."

Solution, I know this sounds crazy, wet sand with soapy water. The soap provides lubrication. In this case, I'm using a foam backed 320 grit wet/dry sandpaper from Mirka. Great for scuffing between topcoats. The foam backing helps keep even "light" pressure that can actually help you from sand-thru. The bonus is the papers wet/dry performance!

Refinishing In Shellac A Veneer Table

2009-03-24T21:18:00.011-04:00

Working on refinishing a teak/veneer coffee table that a friend purchase many years ago in the discount section. I suspected the veneer just de-laminated. However working on the table it was apparent while heating (after stripping the finish off cover the spot with thin cardboard and use medium heat from a household iron to warm the spot, this sometimes reactivates the glue) it wouldn't stick down. So I took a razor blade and slit into 2 of the bubbles and hit it with more heat then while pressing with my finger I could definitely feel something firm. Obviously, some crud must of been trapped underneath the veneer from the factory. The dents and deep scratches have been removed with a hot steam iron along with the alcohol water trick. I think our friends are going to be very surprised. Because of the thin veneer, I didn't want to take a chance of sanding through with my random orbit sander ("ROS") so I block sanded with 220 by hand instead.

Last week, one day our weather hit in the 60's (did you know... shellac isn't temperature sensitive and cold weather even under 40 won't affect the cure, that's a good thing to know way up here in the cold North), so I set up the garage to spray. I used the Zinsser Bulls Eye Amber Shellac 3 pound cut straight from the can (don't forget to strain your shellac it does contain lots of junk,chunks even bug parts) and put down a heavy coat or two. Sanded back with 320, then I decided to have some fun and hooked on to my ROS the Mirka Abralon 1000 and 2000 grit sanding pads to figure out my sheen. Wet the table top with soapy water and WOO HOO. No I didn't electrocute myself, but don't you do that, water and electricity DON'T MIX. Do not use an electric sander for this operation.

I want to achieve a satin finish and get that "close to the wood" feel as possible. I didn't really pile on that much shellac. Just enough to rub. So first, it's necessary to remove the gloss from the grain pockets to match the satin sheen of the higher top surface. To do this, I used 00 steel wool (didn't have any 0000 steel wool) and scrubbed (not hard) in the direction of the grain, then went over the entire top with maroon scuff pad.

Using the 1000 grit Abralon pad will give you approximately satin sheen. Using soapy water as a lubricant, hit it ACE! I Keep the ROS (sander) moving using light pressure (the weight of the sander is all that is necessary)

All done! It's that simple and looks great as is. But! I went ahead and put a coat of wax on to shine things up just a wee little bit....It's so easy guys and gals...you just can't mess up with the Abralon pads. Try them they work great, just as easy using by hand.

Cherry Finish For Poplar - Conclusion

2008-11-16T09:52:00.024-05:00

The Dye Job

Here we are, sprayed with 5 light coats, very light, a mist is a better way of describing, of Gemini NGR Equalizer Dye. Keep the gun moving trying not to spray too heavy. The first few coats looked awful coverage wasn’t very good (didn’t want to blotch). After 3 coats things get better and I was breathing a little easier. Now that the table base was done, time to spray the top. However, while spraying the top, I encountered a problem with the gun. Thinking I had run out of dye I looked into the cup and could see all kinds of grunge mixed in with a ½ full cup of dye. I poured off the cup and removed my cup to examine the gun’s plastic filter and it was plugged. I then discovered my paper filter (paint strainer) screen had partially detached from the paper funnel. Apparently, after using the filter over three (3) consecutive times, the NGR Dye had a reaction with the adhesive holding the filters mesh to the filter cone. Oops, they were latex paint filters. Anyhow, I had to sand back just a little and reapply a few light coats to even things out.

Spray The Oil Stain

Now remember my test board, all the love I put into that thing. That folks was a perfect world. Remember, this project was previously finished with dye and stain and 5 coats of poly.

Ok, here's the deal, its 88 degrees outside with the sun baking my garage and no breeze and humid as hell. So with my gun loaded with the Gemini Black Cherry oil stain I began to spray my first of two planed coats (remember the test board had 2 coats only of Gemini Black Cherry oil stain). Well you can just take that test board a chuck it out the window. As I was spraying my stain, it was dry before it even hit the wood (well pretty close to it anyway). By the time I was done the top was so much darker than the base and looked like crap.

Due to the hot weather, I had no working time! So I washed the entire table down with mineral spirits removing the stain. let it dry over night and hit it again in the morning when it was cooler.

Finally, you have to know when to stop! I love the color of my table and will not be using the General Finishes water based dye as my test board. I could probably lock down my color with shellac or something else and keep going, but that’s it folks I’m stopping with my color right here and don’t want to muddy it up for just a little more brown... I LIKE IT JUST THE WAY IT IS AND DAMN DOES IT LOOK GOOD.

Cherry Finish For Poplar - Part 6

2008-11-01T21:12:00.015-04:00

Finished stripping the base, now I've washed the entire table down with mineral spirits to remove any lingering stripper. So all that's left to do is SAND.

Here is a pic of a little dent I had, here's how to remove it ?

My sanding schedule was first 150 and finishing with 180. End-grain was taken care of by sanding with 320 then finishing with 600. That polishes the end-grain and limits the amount of stain absorbed.

Cherry Finish For Poplar - Part 5

2008-10-03T23:53:00.025-04:00

Below are pictures of my test board that is divided into sections with blue painters tape then sprayed with the various NGR dyes and stains. Each required approximately 4 to 5 coats for an even color. Remember our various base colors will enhance our oil stains applied over top giving us that warm tone underneath together with evening out the darker heart and light sap wood.

First area, a base coat of Gemini Equalizer NGR stain.

Second area, a base coat of Gemini New England Maple NGR Dye.

Third area, a base coat of Gemini Raw Sienna NGR Dye.

Testing my table color sequence through the spray gun.

First, the Gemini Equalizer NGR Stain.

Second, 2 coats of Gemini Black Cherry oil stain over top the completely dry Gemini Equalizer NGR Stain.

Third and final, 3 coats of General Finishes water based Vintage Cherry Dye over top of the completely dry Gemini Equalizer NGR Stain and Gemini Black Cherry oil stain.

Here's a view of my practice board and notice the 3 lighter color sections closest to you. I'll be working out color and tones for a keeping chest build that is planed down the road.

Cherry Finish For Poplar - Part 4

2008-09-21T20:22:00.023-04:00

Spraying the color:

I’ve decided with the darker cherry color for my table (number C4). Spent the better part of 6 hours spraying my dye and stains to my test board. Holy crap guys/gals this was one aggravating day and an amazing day all rolled up into one. I’ve must of cleaned the spray gun several hundred times (not really but sure felt like it) between all the combination's of dye/stain/water based.

NGR dye and fast drying oil stain pretty much dries instantly. So you don’t have the work time like the box-store hand wiping stuff. I just couldn’t seem to find my color that I matched confidently by hand wiping. I’m telling you guys/gals, this fast drying dye/oil is a whole different animal, light clear and even color.

By dinnertime I knew I was getting close, so had a quick dinner thought about it. Went to the garage… turned the board over filled the gun and sprayed. I was done and nailed the color in no time, just that fast.

In conclusion, the biggest problems you will experience is keeping the coats light and to slow down. When you slop on box-store stain by hand its slopping and mopping hitting it again move! move! move! Spraying is a different move! move! move! Hard to explain…you need to experience it. Once you do…you’ll never want to go back.

My small spray gun is Vaper HVLP detail (touch-up gun) $26.00with a 1.0 fluid needle. Max gun air pressure is 21psi. Just love this little guy. My only complaint is the cup cover (plastic cap) had cracked all around the vent not long after I purchased it. The orange looking thing attached to the gun is a small line dryer. Lets not take a chance of water from the compressor getting in the finish. You can find these at the auto body store, get 2 for I think $20.00The larger spray gun is a Husky HVLP brand (reportedly made by Campbell Hausfeld) Around $79.00ish with a 1.4 fluid needle. Max gun air pressure is 40psi. I’ve sprayed poly with this gun at 10psi… less over spray, works real nice.

PLEASE read your dye and stain cans for proper use, handling and clean up. Dispose all rags/paper towels properly. As we all should know rags/paper towels soiled with dye’s finishes, solvents are a SPONTANEOUS COMBUSTION fire hazard. Dispose of properly!
Don’t forget to buy some paint strainers. Who knows what kind of crud is swimming in your dyes/stains waiting to clog up you spray gun. One last thing…be good to your gun keep him clean, even more so, with water based products

Cherry Finish For Poplar - Part 3

2008-09-13T21:59:00.030-04:00

You have to be diligent about writing all this stuff down. Believe me after a while you forget. I decided to wipe these dyes and stains to quickly attain color. Didn’t feel like loading the spray gun and all that. So I sanded to 180 and applied the NGR dye directly to the raw wood with a rag.

A) Base of 1 coat Gemini Raw Sienna NGR dye
B) Base of 1 coat Gemini New England Maple NGR dye
C) Base of 2 coats Gemini Equalizer NGR stain

A1) 1 coat of Gemini Heirloom oil stain
A2) 1 coat of Gemini Black Cherry oil stain
B3) 1 coat of General Finishes water base Black Cherry
C4) 1 coat of Gemini Black Cherry oil stain & 1 coat of General Finishes water based Vintage Cherry dye stain
A5) 1 coat of Gemini Red/Brown concentrate water basedmixed 1 part concentrate to 3 parts water. Then anothercoat at 2 parts concentrate to 2 parts water.
A6) 1 coat of General Finishes water based Vintage Cherry dye stain
A7) 1 coat of General Finishes water base Black Cherry

This is what I’m leaning to. We have a small table in the house and decided to match that.

Cherry Finish For Poplar - Part 2

2008-09-03T21:00:00.014-04:00

The spray finishes I'll be using are quality professional finishes from Gemini Coatings specifically, NGR (non grain raising) dyes and oils stains, I have a small sample of a water based concentrate to try as well, together with General Finishes water based dye and stain.

This is my practice board. The table top has lots of sapwood and heartwood so I need to play a little. My only concern since my table was previously finished...the dye and stain will react totally different than my fresh practice board but the color should be close. I'm looking for a brownish tone cherry.

My color range is a dark old cherry bed post (pictured to the left) and a lighter cherry board (pictured to the right) Looking forward to using a professional spray on product like Gemini Coatings. So on to the next step which is a little play time experimenting with various finishes looking for that perfect color combination.

Cherry Finish For Poplar - Part 1

2008-08-25T21:29:00.071-04:00

I recently came across this picture of a coffee tabletop I made a while back. Just wanted to step out of my safe zone, Minwax. I thought I read enough to understand the ½ pound cut of shellac thing and using alcohol dye. Even thought I could handle the sapwood that perhaps I shouldn't have built with? Only wanted to make poplar look like cherry. You get the idea. This is what pissed me off about finishing... take a look.

Lets Get Started

I’ll take the finish off using a chemical stripper. I like thick rubber gloves, because the steel wool will chew through most regular "finishing" rubber gloves. Not pictured are my safety goggles. Always wear safety goggles for splashes and from those vapors which can sting the eyes. Work in a well-ventilated area or best outdoors. I apply the stripper with a natural hair paintbrush. Let is sit on the surface till the old finish has mostly lifted and bubbled up. I then remove the heavy layer of goo with a large putty-knife wiping it into paper towels. Then I'll go back over the area applying more stripper...let it sit on the surface a few minutes and while the surface is still wet, scrub the surface in the direction of the grain removing finish that remains down in the pores of the wood. Your steel wool will be come full of removed finish just like a sponge soaking up water.

Alright, top is now stripped then I'll be moving on to the table base. When everything is completely stripped wash the wood down with mineral spirits removing any residue.

After The Deal - Widow Maker

2007-09-16T20:54:00.002-04:00

It’s now around 8:30 pm my Son and I have returned from Lowe’s with ma new band saw. I backed my truck into the garage at a sharp angle so the corner of my tailgate is close to the door of the house. I know, at this point your thinking I’m on the telephone calling one of my neighbor’s or bud’s for help. After all, this does weigh around 200ish pounds and has to go down the basement. Nope, was gonna do it myself! First thought was to lighten the load. I climb into the back of the truck and open the box and took out everything I could, which was only the motor and stand. Geez what is that only 30 pounds?

I taped the box backup and slid it to the tailgate. The plan was once the box is off the tailgate and on the house step. I could tip the box over slowly and into our house. Sometimes plans don't go so well. The angle of my tailgate to the door step was to severe so the corner of my tailgate was going to dig into the box as I lowered it. So I had to let it down standing on end directly behind the tailgate. Now for the first time, I feel the full force of how heavy this damn thing really is.

After using some imagination and a couple of 2x4's a dirt shovel, all aids to lift the box up and onto the step of the house. I could then tip the box back and into the house on two rugs enabling me to push (slide) the box over the kitchen floor.

Its go time baby! We've arrived at the stairs. I felt I could control the slide of the box down the stairs if I could get in front of the box, although very dangerous - something like stepping in the front of a speeding car. Needless to say I was successful for the first six or seven steps. All of the sudden I began to feel 220 pound box telling me what to do and picked up momentum. As I was being forced downward towards the 90 deg. section of the walled portion of our stairs. I was able to open my legs just far enough so the box could pass through and stopping short of hitting the wall. As this was taking place, I was falling backwards and my butt smashed into the wall. My God, what just happened? This thing could of killed me! What was I thinking? As I turned around I envisioned my rear-end had pumped a big hole through our drywall. I was fortunate and nothing happened to me or the drywall. After a quick check to make sure my back still worked. I did manage to wrangle the saw and box to my shop.

"The Deal" - 14" Delta Band Saw

2007-09-10T20:03:00.001-04:00

Had my eye on the Delta 14″ model 28-276 with the 3/4 hp motor. I'm sorta known as a cheap a**, I was waiting for a sale that would never come. Well a few weeks ago I was at Lowe’s with my 8 year old Son in the tool area debating the fact this stupid saw will never go on sale, that’s when my Son looked up to me and said frankly, Dad, why don’t you just buy it? Ya know, that kid of mine has a point! So down we went on our hands and knees looking and found a Delta band saw with its carton damaged pretty good. At that point, it was my Sons lucky day. He was able to witness his old man the “cheap a**” in action negotiating with the store Manager a mutually beneficial discount. We've arrived at the point my Wife would roll her eyes at me and find something else to do in the store. My Wife has grown up in sales and I can hear her voice “sales people need to make a living too.” But I want that saw for less money. :)

I’m lucky in the fact I live near a large city and have many choices when it comes to purchasing machinery. We have several Lowe’s/Home Depot’s a Rockler and Woodcraft all within a 35 mile radius. Through the years I’ve learned to be a patient buyer and most of my machines were picked up either as floor models or via a damaged carton discount. Floor models typically give you the best discount of 15% to 20% while damaged cartons offer approximately 10%. Floor models usually have a minor part or owners manual missing. Damaged cartons are usually just that - damaged cartons. Take your time in the stores and look for a damaged carton. I’ll almost bet you will find at least one carton with a crushed end or cuts and tears. Don’t waste your time with the sales person. Ask to speak to the department Manager. He/she has the authority to issue the discounts.

The Manager will try to tell you nothing is wrong with a little "carton damage" and that’s just the box doing its job. Remember, they don’t want a spoiled box on the store floor. For goodness sake they damaged it while stocking. Explain to the Manager, due to the carton being opened through tears. Nuts or bolts are probably missing! Damage is likely to sheet metal from a hard drop like that! Use your imagination. Ask the store Manager you’d like to buy it - how about knocking 15% off the price. The Manager will tell you he/she can’t do that. However, say to the Manager, a nice discount would be good way to offset my time having to chase down missing parts and fixing any damage. My experience in those negotiations are the store will almost always give you a max of 10% discount for carton damage.